Modern Accent Armchair Assembly Instructions (SKU:F-COO-W2678P183188)

This upholstered accent chair features reinforced arm rest frames, a structured seat and back support system, and removable zip-fastening cushion covers. Following the correct assembly sequence ensures proper alignment and long-term durability.

Read all instructions before beginning assembly.

SAFETY INFORMATION

Important

Keep children and pets away during assembly.
Small parts may present a choking hazard.
Do not stand on the chair.
Maximum weight capacity: 113 kg (250 lbs).
Use only on a stable, level surface.
Do not use it if parts are missing or damaged.

Caution

Two-person assembly is recommended.
Handle components carefully.
Ensure adequate lighting and workspace.

PARTS & HARDWARE

Illustrated parts list including chair frames, panels, and cushions.

Parts Identification

Part	Description	Quantity
A	Left Arm-rest Frame	1
B	Right Arm-rest Frame	1
C	Back Frame	1
D	Seat Frame	1
E	Seat Cushion	1
F	Back Cushion	1
G	Crosspiece	1
L	Seat Cover	1
M	Back Cover	1

Hardware List

Part	Description	Quantity
H	M8 x 40mm Screw	8
I	M8 x 60mm Screw	4
J	Allen Key	1
K	Cork Pads	12

BEFORE YOU BEGIN

During frame assembly, secure screws loosely to allow adjustment.
Final tightening will be completed after full alignment.

Estimated Assembly Time: 25–35 minutes

STEP-BY-STEP ASSEMBLY

Follow the steps below to assemble your Modern Accent Armchair with Wooden Frame properly and safely.

Step 1: Attach Arm Frames to Crosspiece

Diagram showing two arm frames connected by a base bar.

Position Left Arm-rest Frame (A) and Right Arm-rest Frame (B) facing inward.
Align Crosspiece (G) between the lower inner sections.
Insert the M8 × 60mm Screws (I) on both sides and tighten them using the Allen key (J).

Step 2: Install Seat Frame (Front)

Detail of the front seat panel being secured with bolts.

Place the Seat Frame (D) between the arm frames.
Insert the M8 × 40mm Screws near the front of the seat first.
Tighten the screws to 70% using the Allen key (J).

Step 3: Install Seat Frame (Rear)

Detail of the rear seat panel being attached to frames.

Insert the remaining M8 × 40mm Screws (H) into the back of the seat.
Use the Allen key (J) to tighten the screws to 70%.
Confirm that all components are properly aligned before proceeding.

Alignment Check

Inspection Point	Confirmation
Arm Frames	Parallel and level
Seat Frame	Centred
Crosspiece	Flush

Step 4: Install Back Frame

Diagram showing back panel being bolted between two side frames.

Position Back Frame (C) between upper rear sections of the arm frames.
Insert M8 x 40mm Screws (H).
Tighten the screws loosely using the Allen Key (J), do not fully tighten yet.
Keep connections adjustable.

Step 5: Secure All Hardware

Diagram showing 100% tightening of all chair frame bolts using Allen key J.

Confirm full frame alignment.
Once alignment is confirmed, fully tighten all previously installed screws using the Allen Key (J).
Ensure no gaps remain at connection points.

Step 6: Cushion Expansion

Icon showing vacuum-sealed cushions being opened with scissors to expand.

Carefully open the compression packaging.
Remove Seat Cushion (E) and Back Cushion (F).
Allow cushions to expand for 24 hours before use.

Step 7: Install Cushion Covers

Visual guide showing foam inserts being placed into fabric covers.

Insert Seat Cushion (E) into Seat Cover (L).
Close the zip completely.
Insert Back Cushion (F) into Back Cover (M).
Zip closed and smooth fabric evenly.

Step 8: Install Cork Pads

Illustration of small protective pads being applied to chair legs.

Turn the chair slightly to access the bottom of each leg.
Insert Cork Pads (K) into designated holes on chair legs.
Press firmly until fully seated.
Confirm the chair rests evenly on the floor.

Step 9: Final Cushion Placement

Drawing showing the correct position for seat and back cushions.

Place Seat Cushion (E) on Seat Frame (D).
Position Back Cushion (F) against Back Frame (C).
Adjust both cushions to ensure they are centred and aligned.

ASSEMBLY COMPLETE

The chair is now ready for use.
Proper alignment ensures long-term stability and performance.

Line drawing of a finished modern armchair with cushions.

TROUBLESHOOTING GUIDE

Assembly Issues

Problem	Solution
Arm frames misaligned	Ensure both frames rest flat before securing hardware.
Crosspiece uneven	Centre evenly before fastening.
Seat frame offset	Reposition evenly before final tightening.
Back frame holes misaligned	Adjust angle slightly to align naturally.
Joint spacing visible	Apply firm pressure while securing hardware.
Packaging inside frame	Remove internal packing material before final tightening.

Post-Assembly Issues

Problem	Solution
Chair unstable	Confirm placement on a level surface.
Cushion uneven	Redistribute filling by hand.
Fabric wrinkles	Smooth outward from centre.
Covers tight during installation	Compress cushion slightly while inserting.
Floor friction noise	Clean bottom contact points.
Chair leans	Confirm cork pads are evenly seated.
Zip resistance	Align fabric edges before pulling.

MAINTENANCE

Inspect hardware periodically.
Clean frame with a soft, dry cloth.
Vacuum cushions regularly.
Avoid moisture exposure.
Protect from prolonged direct sunlight.
Rotate cushions periodically for even wear.

You can download the complete assembly manual for the Modern Accent Armchair (SKU:F-COO-W2678P183188) for your reference.

Download Manual(PDF)

FAQs

1. Does the chair require wall support for stability?

No, the chair is fully freestanding. When assembled correctly and placed on a level surface, it does not require wall support for normal household use.

2. Does the seat firmness change over time?

Like most upholstered furniture, the cushion may soften slightly with regular use. Rotating and fluffing periodically helps maintain shape and comfort.

3. Can this chair be used in a covered patio or balcony?

It is designed for indoor use. If placed in a covered outdoor area, ensure it is protected from moisture, humidity, and direct sunlight to prevent material wear.